A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings

Mihary R. Ito, Chengfang Duan, Leonardo Patricio Chamorro Chavez, Aimy Wissa

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Even though Unmanned Aerial Vehicles (UAVs) operating at low Reynolds numbers are becoming common, their performance and maneuverability are still greatly limited due to aerodynamic phenomena such as stall and flow separation. Birds mitigate these limitations by adapting their wings and feather shapes during flight. Equipped with a set of small feathers, known as the alula, located near the leading edge and covering 5% to 20% of the span, bird wings can sustain the lift necessary to fly at low velocities and high angles of attack. This paper presents the effect on lift generation of different placements of a Leading-Edge Alula-inpsired Device (LEAD) along the span of a moderate aspect-ratio wing. The device is modeled after the alula on a bird, and it increases the capability of a wing to maintain higher pressure gradients by modifying the near-wall flow close to the leading-edge. It also generates tip vortices that modify the turbulence on the upper-surface of the wing, delaying flow separation. The effect of the LEAD can be compared to traditional slats or vortex generators on two-dimensional wings. For finite wings, on the other hand, the effect depends on the interaction between the LEADs tip vortices and those from the main structure. Wind tunnel experiments were conducted on a cambered wing at post-stall and deep-stall angles of attack at low Reynolds numbers of 100,000 and 135,000. To quantify the aerodynamic effect of the device, the lift generated by the wing with and without the LEAD were measured using a 6-axis force and torque transducer, and the resulting lift coefficients were compared. Results show that the location of the LEAD yielding the highest lift enhancement was 50% semi-span away from the wing root. Lift improvements of up to 32% for post stall and 37% for deep stall were obtained at this location, demonstrating that the three-dimensional effects of the LEAD are important. The lift enhancement was also more prominent on a finite moderate aspect-ratio wing (3D) than on an airfoil (2D), confirming that the LEAD is a three-dimensional device. Identifying the configurations and deployment parameters that improve lift generation the most is needed to design an adaptive LEAD that can be implemented on a UAV wing for increased mission-adaptability.

Original languageEnglish (US)
Title of host publicationMechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies
PublisherAmerican Society of Mechanical Engineers (ASME)
ISBN (Electronic)9780791851951
DOIs
StatePublished - Jan 1 2018
EventASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018 - San Antonio, United States
Duration: Sep 10 2018Sep 12 2018

Publication series

NameASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018
Volume2

Other

OtherASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018
CountryUnited States
CitySan Antonio
Period9/10/189/12/18

Fingerprint

Reynolds number
Birds
Vortex flow
Flow separation
Angle of attack
Unmanned aerial vehicles (UAV)
Aspect ratio
Aerodynamics
Wall flow
Maneuverability
Pressure gradient
Airfoils
Wind tunnels
Transducers
Turbulence
Torque

ASJC Scopus subject areas

  • Biomaterials
  • Civil and Structural Engineering

Cite this

Ito, M. R., Duan, C., Chamorro Chavez, L. P., & Wissa, A. (2018). A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings. In Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies (ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018; Vol. 2). American Society of Mechanical Engineers (ASME). https://doi.org/10.1115/SMASIS2018-8170

A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings. / Ito, Mihary R.; Duan, Chengfang; Chamorro Chavez, Leonardo Patricio; Wissa, Aimy.

Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies. American Society of Mechanical Engineers (ASME), 2018. (ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018; Vol. 2).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Ito, MR, Duan, C, Chamorro Chavez, LP & Wissa, A 2018, A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings. in Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies. ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018, vol. 2, American Society of Mechanical Engineers (ASME), ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018, San Antonio, United States, 9/10/18. https://doi.org/10.1115/SMASIS2018-8170
Ito MR, Duan C, Chamorro Chavez LP, Wissa A. A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings. In Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies. American Society of Mechanical Engineers (ASME). 2018. (ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018). https://doi.org/10.1115/SMASIS2018-8170
Ito, Mihary R. ; Duan, Chengfang ; Chamorro Chavez, Leonardo Patricio ; Wissa, Aimy. / A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings. Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies. American Society of Mechanical Engineers (ASME), 2018. (ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018).
@inproceedings{dea9a6afba9e4acab57ff473432e5882,
title = "A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings",
abstract = "Even though Unmanned Aerial Vehicles (UAVs) operating at low Reynolds numbers are becoming common, their performance and maneuverability are still greatly limited due to aerodynamic phenomena such as stall and flow separation. Birds mitigate these limitations by adapting their wings and feather shapes during flight. Equipped with a set of small feathers, known as the alula, located near the leading edge and covering 5{\%} to 20{\%} of the span, bird wings can sustain the lift necessary to fly at low velocities and high angles of attack. This paper presents the effect on lift generation of different placements of a Leading-Edge Alula-inpsired Device (LEAD) along the span of a moderate aspect-ratio wing. The device is modeled after the alula on a bird, and it increases the capability of a wing to maintain higher pressure gradients by modifying the near-wall flow close to the leading-edge. It also generates tip vortices that modify the turbulence on the upper-surface of the wing, delaying flow separation. The effect of the LEAD can be compared to traditional slats or vortex generators on two-dimensional wings. For finite wings, on the other hand, the effect depends on the interaction between the LEADs tip vortices and those from the main structure. Wind tunnel experiments were conducted on a cambered wing at post-stall and deep-stall angles of attack at low Reynolds numbers of 100,000 and 135,000. To quantify the aerodynamic effect of the device, the lift generated by the wing with and without the LEAD were measured using a 6-axis force and torque transducer, and the resulting lift coefficients were compared. Results show that the location of the LEAD yielding the highest lift enhancement was 50{\%} semi-span away from the wing root. Lift improvements of up to 32{\%} for post stall and 37{\%} for deep stall were obtained at this location, demonstrating that the three-dimensional effects of the LEAD are important. The lift enhancement was also more prominent on a finite moderate aspect-ratio wing (3D) than on an airfoil (2D), confirming that the LEAD is a three-dimensional device. Identifying the configurations and deployment parameters that improve lift generation the most is needed to design an adaptive LEAD that can be implemented on a UAV wing for increased mission-adaptability.",
author = "Ito, {Mihary R.} and Chengfang Duan and {Chamorro Chavez}, {Leonardo Patricio} and Aimy Wissa",
year = "2018",
month = "1",
day = "1",
doi = "10.1115/SMASIS2018-8170",
language = "English (US)",
series = "ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018",
publisher = "American Society of Mechanical Engineers (ASME)",
booktitle = "Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies",

}

TY - GEN

T1 - A leading-edge alula-inspired device (LEAD) for stall mitigation and lift enhancement for low Reynolds number finite wings

AU - Ito, Mihary R.

AU - Duan, Chengfang

AU - Chamorro Chavez, Leonardo Patricio

AU - Wissa, Aimy

PY - 2018/1/1

Y1 - 2018/1/1

N2 - Even though Unmanned Aerial Vehicles (UAVs) operating at low Reynolds numbers are becoming common, their performance and maneuverability are still greatly limited due to aerodynamic phenomena such as stall and flow separation. Birds mitigate these limitations by adapting their wings and feather shapes during flight. Equipped with a set of small feathers, known as the alula, located near the leading edge and covering 5% to 20% of the span, bird wings can sustain the lift necessary to fly at low velocities and high angles of attack. This paper presents the effect on lift generation of different placements of a Leading-Edge Alula-inpsired Device (LEAD) along the span of a moderate aspect-ratio wing. The device is modeled after the alula on a bird, and it increases the capability of a wing to maintain higher pressure gradients by modifying the near-wall flow close to the leading-edge. It also generates tip vortices that modify the turbulence on the upper-surface of the wing, delaying flow separation. The effect of the LEAD can be compared to traditional slats or vortex generators on two-dimensional wings. For finite wings, on the other hand, the effect depends on the interaction between the LEADs tip vortices and those from the main structure. Wind tunnel experiments were conducted on a cambered wing at post-stall and deep-stall angles of attack at low Reynolds numbers of 100,000 and 135,000. To quantify the aerodynamic effect of the device, the lift generated by the wing with and without the LEAD were measured using a 6-axis force and torque transducer, and the resulting lift coefficients were compared. Results show that the location of the LEAD yielding the highest lift enhancement was 50% semi-span away from the wing root. Lift improvements of up to 32% for post stall and 37% for deep stall were obtained at this location, demonstrating that the three-dimensional effects of the LEAD are important. The lift enhancement was also more prominent on a finite moderate aspect-ratio wing (3D) than on an airfoil (2D), confirming that the LEAD is a three-dimensional device. Identifying the configurations and deployment parameters that improve lift generation the most is needed to design an adaptive LEAD that can be implemented on a UAV wing for increased mission-adaptability.

AB - Even though Unmanned Aerial Vehicles (UAVs) operating at low Reynolds numbers are becoming common, their performance and maneuverability are still greatly limited due to aerodynamic phenomena such as stall and flow separation. Birds mitigate these limitations by adapting their wings and feather shapes during flight. Equipped with a set of small feathers, known as the alula, located near the leading edge and covering 5% to 20% of the span, bird wings can sustain the lift necessary to fly at low velocities and high angles of attack. This paper presents the effect on lift generation of different placements of a Leading-Edge Alula-inpsired Device (LEAD) along the span of a moderate aspect-ratio wing. The device is modeled after the alula on a bird, and it increases the capability of a wing to maintain higher pressure gradients by modifying the near-wall flow close to the leading-edge. It also generates tip vortices that modify the turbulence on the upper-surface of the wing, delaying flow separation. The effect of the LEAD can be compared to traditional slats or vortex generators on two-dimensional wings. For finite wings, on the other hand, the effect depends on the interaction between the LEADs tip vortices and those from the main structure. Wind tunnel experiments were conducted on a cambered wing at post-stall and deep-stall angles of attack at low Reynolds numbers of 100,000 and 135,000. To quantify the aerodynamic effect of the device, the lift generated by the wing with and without the LEAD were measured using a 6-axis force and torque transducer, and the resulting lift coefficients were compared. Results show that the location of the LEAD yielding the highest lift enhancement was 50% semi-span away from the wing root. Lift improvements of up to 32% for post stall and 37% for deep stall were obtained at this location, demonstrating that the three-dimensional effects of the LEAD are important. The lift enhancement was also more prominent on a finite moderate aspect-ratio wing (3D) than on an airfoil (2D), confirming that the LEAD is a three-dimensional device. Identifying the configurations and deployment parameters that improve lift generation the most is needed to design an adaptive LEAD that can be implemented on a UAV wing for increased mission-adaptability.

UR - http://www.scopus.com/inward/record.url?scp=85057227955&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85057227955&partnerID=8YFLogxK

U2 - 10.1115/SMASIS2018-8170

DO - 10.1115/SMASIS2018-8170

M3 - Conference contribution

AN - SCOPUS:85057227955

T3 - ASME 2018 Conference on Smart Materials, Adaptive Structures and Intelligent Systems, SMASIS 2018

BT - Mechanics and Behavior of Active Materials; Structural Health Monitoring; Bioinspired Smart Materials and Systems; Energy Harvesting; Emerging Technologies

PB - American Society of Mechanical Engineers (ASME)

ER -